- Weight: 56g
- Dimension: 40×19.7×41mm
- Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v)
- Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v)
- Operating voltage: 4.8 ~ 6.6V
- Gear Type: Metal gear
- Wire length: 32cm
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~6
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5
₹100.00inc.GST 45% off ₹100.00inc.GST 45% off
- Model: 8520
- Shaft Size: 1.0 mm
- Rated Voltage: 3.7 V.
- Wire Length: 6cm
- Prop. Length: 8.5x20mm
- Model: A2212/10T
- Motor KV: 1400
- Max. Efficiency Current: 6-12A
- No Load Current: 0.7A @10V
- Current Capacity: 16A/60S
- High quality stepper motor
- Voltage: DC 5V
- Diameter: 25mm
- Step Angle: 5.625 x 1/64
- Reduction Ratio: 1/64
- Rated voltage ： 5VDC
- Frequency : 100Hz
- DC resistance ： 50Ω±7%(25℃)
- Idle In-traction Frequency : > 600Hz
1. Step Angle: 1.8 degree
2. Voltage: 2.3V
3. Current/phase: 2.8A
4. Resistance/phase: 0.98 ohms
5. Holding Torque: 10.1 kg.cm
6. Rotor Inertia: 275 g.cm2
7. Inductance/ phase (mH): 2.2
8. No. of Leads: 4
9. Weight (kg): 0.65
10. Step Angle Accuracy – (+-) 5%
11. Resistance Accuracy – (+-) 10%
12. Inductance Accuracy – (+-) 20%
13. Detent Torque (kg-cm): 0.36
14. Length (mm): 74
15. Frame Size (mm): 57×57
16. Shaft Length (mm): 19
17. Shaft Diameter (mm): 8.5
- ULN2003A motor driver chip
- Chip all the pins already leads for easy connection to use
- 5-12V power supply
- 4-way signal indicator
- Step angle: 5.625 x 1 / 64
- Reduction ratio: 1 / 64
- Phase: 4
- Current / Phase: 5V
The metal gears have better wear and tear properties.
Gearbox is sealed and lubricated with lithium grease and requires no maintenance.
Although motor gives 100 RPM at 12V, motor runs smoothly from 4V to 12V and gives the wide range of RPM, and torque.
The shaft has a hole for better coupling.
Operating Voltage(V): 12
Rated Torque(kg-cm): 2.9
Stall Torque(kg-cm): 11.4
Low density: lightweight, low inertia.
Capability to absorb shock and vibration as a result of elastic compliance.
Ability to operate with minimum or no lubrication, due to inherent lubricity.
The relatively low coefficient of friction.
Operating Voltage(VDC): 3~12
Shaft Length (mm): 8.5
Shaft Diameter (mm): 5.5 (Double D-type)
No Load Current: 40-180mA.
Rated Speed(After Reduction): 150 RPM
Rated Torque: 1 Kgcm
Operating Voltage : 2.5 ~ 6V
Operating Current : 130 ~ 220mA
Flow Rate : 80 ~ 120 L/H
Maximum Lift : 40 ~ 110 mm
Continuous Working Life : 500 hours
Driving Mode : DC, Magnetic Driving
Material : Engineering Plastic
Outlet Outside Diameter : 7.5 mm
Outlet Inside Diameter : 5 mm